Search results

Hey folks haven't posted in a while . . . I'm looking for a King Cab pick up truck in Portugal and have always liked the look of the old D21's with vented bonnet. What year and engine would you guys recommend? It seems that most (if not all) D21's in Portugal have the TD25 diesel engine...

Or can anyone recommend good aftermarket water pump brands . . .

Hey folks, Looking at a 91 Urvan with Z24 carb engine that needs a new water pump and been told Genuine Nissan is the way to go as the aftermarkets options are no good (noisy and poor thermoreg). Struggling to find a Nissan one in Australia at the moment though, any ideas? Ta, Rich

Found most of my answers here; 👍🏼 Hoist would be nice!

Is there anything else you need besides the oil buddy? I've got all the oil just need to get off my arse and do it . . . Read that it's best to remove the drain plug first and then the fill plug, are any of these hard to locate or pour the oil? ta, Rich

Bro I'm co Bro I'm confused how come you needed an extra bushing, I thought you got them all with the control arm kit . . .

Soo far I have compiled the following list of steering/suspension parts to replace . . . LCA arm assembly LCA arm chassis bush Lower Ball Joints UCA arm assembly UCA arm chassis bush Upper Ball Joints Drag Link DL bushes Sway Bar D Bush Tie Rod Ends Idler Arm Shocks all round Rear Leaf Springs...

Sounds good buddy . . . are you back in Central Vic? I'm only looking to do a stock refresh really since I don't do much proper off-roading its just a farm Ute essentially. Would be great if there were a shopping list somewhere on the forum of all the parts/part numbers needed to do a full...

Where did you source this cheaper replacement buddy? Ta, Rich

Hey buddy the video wasn't that helpful in the end . . . I only replaced the injector seals, to do the injectors you have to remove the rocker cover as well. I removed the bracket holding all the vacuum hoses on top of the engine (3x bolts), then the throttle body, EGR valve & pipes (leaving...

Also any tips on removing the seal without dropping/losing the spring…

I think my main question is do I have to remove the inlet manifold and/or rocker cover? Also thinking whether I replace the glow plug seals, rocker cover gasket and inlet manifold gasket at same time . . .

That's right buddy pretty happy with the new clutch no more shudder on pull away and gear changes feel much smoother. So I degreased the whole engine pretty much and washed it down with a high pressure hose several times and its blatantly coming from the injector seals / pooling up on top of the...

Hey folks traced an oil leak back to the injectors (oil pooling up on top of the inlet manifold) and pretty sure it's the injector seals. Watched a quick YouTube video looks pretty straight forward once all the hoses and electrics are out the way. Just pop out the old seals and replace and...

yeah there was no indent or anything on the tube itself and it wasn't big enough diameter to fit over so dropped it in the hole 🤷‍♂️

Hey Bro I pulled it out and couldn’t see an O-ring rubber in sight…I’d already ordered one so I drop it in the hole as it wasn’t a fit for round the tube itself 👍🏼 In other news I just found the source of the main leak! Dam injector seals staring me in the face all this time!!! Shame I just...

Update folks. So I got an Exedy Clutch and Genuine Rear Main seal online but chickened out on the fitting! I took it to PMA in Melbourne a supposed Nissan Specialist in Melbourne although I didn’t see many Nissan’s there. Pretty good service and they quoted me a grand for the job. Plus they...

Ha nice I've got a couple of friends with tools willing to help so no excuses really! Although thought I'd get a couple of quotes for good measure and see what everyone's paying for clutches. Best I've seen so far is Exedy Clutch NSK-7373 for 470 bucks online and the Genuine Rear Main Seal for...

Thanks a lot for the reply Bro . . . I’m nearby Seymour in Central Victoria . . . I could pull the truck into the Shed with concrete surface, got two 3T stands and one Trolley Jack, no lift of any kind. What needs to happen with the spigot bush/bearing? Do I need a bearing puller? Nah not...

Ok so just confirmed my oil leak is the real main seal (pretty likely all along from reading posts on here) . . . So going to get all the parts together I need, assuming its just the real main seal and new clutch (since the truck has 300km's)? What is the best value replacement clutch or...