Search results

Nissan Navara Forum

Help Support Nissan Navara Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Been a while

    New tray cover

    Finally! I managed to get the cover replaced and thought she looked a bit naked without the "Foo eyes" and grenade... so I painted a new one on the rear door..
  2. Been a while

    Battery light not illuminating on ignition on position, alternator or dash cluster issues?

    Here's one for the brains trust! Battery check light not illuminating on "key on position" . It was staying on after start up and going off whilst you raised the revs but, now it's going off whilst on idle? Alternator doesn't seem to be giving out the right charge rate either? Do you think...
  3. Been a while

    Horn stopped working?

    Howdy all, I fitted up an Air Horn years ago and it's been working fine untill last week :( I can here relay clicking so replaced the genuine one under the bonnet and its still not working "still clicking", checked fuses earths etc , nothing wrong there.. Air horn works when wired directly to...
  4. Been a while

    Coolant leak?

    This is a strange one.. every now and again I end up with a small puddle of coolant on the floor so I finally motivated myself to go looking for the leak.. The only place I can see where it could be coming from is the heater pipe to the head and thermostat area, orrrr from between the head and...
  5. Been a while

    Dream Zd build!

    Maybe this is a better way to go about it :) if you had a chance to build "a mild" zd how would you go about it? What would you fit?
  6. Been a while

    Who's building zd motors and gearboxes!?

    Howdy all :) "long time no piss'n'moan" ... I'm thinking of putting some money into my old girl aaaand thinking motor rebuild, and box.. Anyone got any suggestions of who's the "go to" shops for zd builds, any state of Australia! Any lists and suggestions regarding build parts etc, love...
  7. Been a while

    Water leak and A Pillar shorkle re-fit..

    I have been chasing this stinking water leak for ages, had the vinyl flooring out for months whilst I try working it out.. Had the new screen fitted! Silicone on all the "old" original A Pillar fixings and still no joy! Cleaned the skuttle and guards water drains! Still no joy! Anyway...
  8. Been a while

    D22 Hood gas struts, I can't find much!

    As the title reads, some how I got the idea of doing this from someone on utube! They're a good kit, a little expensive but they sit "to me" in a crapy position! There's nothing out there for the D22! Anyone know of anything? I'm thinking of making up some mounting brackets and fitting a...
  9. Been a while

    D22 Hood gas struts, i cant find a kit???

    As the title reads, some how I got the idea of doing this from someone on utube! They're a good kit, a little expensive but they sit "to me" in a crapy position! There's nothing out there for the D22! Anyone know of anything? I'm thinking of making up some mounting brackets and fitting a...
  10. Been a while

    Who's the forum moderator here!

    New posts! Whats happening there?
  11. Been a while

    Best clutch job yet!

    Watch from the 6 min mark!
  12. Been a while

    300000k+ front end service, H.D Drag Link set up, Lower Control Arms- Ball Joints, Bushing replacement. Sway bar bush and link kit. Wheel Bearing R/R,

    Howdy all, going by the left hand outer "tyre wear" things need to be done to correct the issue.. dammit! Last alignment they said they had issues with it and dropped the hight, but obviously thaAat didn't work!!! So I've been slowly picking up and gathering the parts needed to give the...
  13. Been a while

    U.C.A Ball joint spacers! Anyone know the "who's got and what" about them?

    Howdy, looking to correct an issue with wheel alignment and after market U.C.A by Snake Racing, looking for a set of spacers.. 12mm, 15mm to 20mm tops, anyone got a machine shop? These U.C.A use the D21 Upper Ball joint also! Thanks..
  14. Been a while

    Plasic Slim line fuel containers/jerry cans

    Howdy all, just got these today.. These are the 20 lt ones, you can get 30lt ones also.. I wanted black but cost killed that, you can get them in black, but the postage and shipping killed it.. So i had to settle for the army green :) localy sorced in Melbourne for $95ea.. yup, expensive but...
  15. Been a while

    Headlight upgrade to led...

    Yeassss i know, l.e.d's in standard headlight fittings....but! I had to do something. .. Well at least they're not h.i.d i guess but i had to do something with the Navs headlights.. I noticed these on special whilst looking for new globes after losing the low beams.. These are not the real...
  16. Been a while

    EngineGaurd fitting...

    Howdy all, i thought I'd fit one of these baby's up before I try for W.A :) I grabbed the two sensor one and put one sensor on the front left of the head and, the other at the rear.. i was going to put the second one on the oil but, that will need some work finding a place to fit it too and...
  17. Been a while

    Breather check. ..

    Noticed this little sucker the other day on her fluids change. .. It had cracked and come away at the very top, strange, i didn't think the box would move thay mich to brake it...
  18. Been a while

    Replacing Ignition lock assembly , L/R Door locks

    It's got me twice now, stuck for a few minutes playing locksmith in the Carpark! 300'+ k's and she's showing:( Anywaysss, I've been thinking of getting new keys cut, to try and solve this, but then I thought the barrels will be just as worn! Sooo for the hell of it I though I'd replace the...
  19. Been a while

    Moto x track for 4x4 in Vic

    Want to thrash your 4x4 on over 2 k's of track.. The bike track is closed but we have a small window for 4x4 use! Woohoo Camping and amenities, small groups only, you will have the track to yourselves, one group at a time so no one else... Must be fully insured! Signed waver etc call 0499...
Back
Top