Search results

Hi. Do you guys know if the steering rack of the Pathfinder R50 is interchangeable with Navara D22? thank you

Yes. The readings come from torque app (Bluetooth odbii).

Hi. My boost reading through the app is generally 5-10 psi. Under acceleration and 3k+ revs it reaches 20 psi and then I have the sudden vacuum on the meter. No black smoke (at least nothing so bad I could see any dark clouds through my back mirror). I would expect the pressure to build to 20...

Hi all. Would I need to measure them first, or is there a definite way to say what size is OK by the model year? 2.5 Diesel YD25 E3 How about the back? D40 with discs in the back is the same as R51 pathfinders? How about pads? Blindly going for it or are there also options with spring both...

Hi. There is so many topisc / answers "maybe boost is low" or "check the solenoid"... Would that mean there is no boost sensor that we could check using ODBII scanner?

I am suprised with the "regular cleanup" requirement. YD25 ECU apparently does not throw error and does not need the hole. 3.0 may be different. I had it blocked with a plate with a hole in it for the sensor in 2.0 Ford mondeo and for 3 years there was no engine code, so only experience I have...

I would try the plate first. Looks like you can achieve 90% of the effect with 5% of the cost.

The engines came as Euro 3, 4, 5 (5 is I guess the 140kW). Some major changes were about 2010 too. I would say it wouldn't as e.g. injectors are different. Older ECU could accept them or not. As a minimum you would probably need the older engine with ECU but the wiring can be different too. E3...

It sounded like a bad metallic rattle. I was sure it is the timing chain rubbing against the casing and it was indeed very loose. I got the timing kit, bit of drama removing the harmonic balancer (850Nm electric impact wrench did the job, 200 Nm did not, 400Nm no idea - it did not fit). After...

Good pick. Re timing chains - absolutely - I have all the parts waiting to put them in. I just saw the damage on the balance shafts on the job of replacing the timing. The whole timing sequence will be replaced. The main question because of new circumstances is: can I get away by doing only the...

Yes - it has all fallen apart. I found one broken tooth just resting on a tensioner so it was flying all over the place. I removed the C clip hoping i could just get rid of that toothless gear, but no luck - it is secured by the bolt which looks impossible to remove until the whole unit comes off.

Thanks. That's the idea :) So I was thinking about removing the cog wheel that drives it. This will get out of time, but hence I would probably need to a) get rid of it totally b) replace - it will probably be out of time anyways and there must be a way to time it. There was something posted...

Hi, Looks like you know stuff about balance shaft removal. My front scissor gear on the balance gear lost half of it's teeth and springs and pins are probably gone. I can spin it freely, no spring tensoin. No locking at 2-3 teeth turn distance travel. My car is stuck on the parking lot and my...

Looks like it is scisor gear, part of idler gear. I found the video below. There is no results when looking for parts. Is there any other name for it? Looks like it comes only as used whole units. Looks like a big job. Would I need to undo the subframe? What if I just removed the big gear that...

Thanks. Based on your information, I decided to look at the bottom chain too. Tensioner is out by around 10mm so quite stretched too. That means I got the balancer out! :) My 1/2 inch bar with a pipe on it was bending by about 15 degrees. It would snap before it goes. Btw the only way to lock...

Hi all. When replacing the timing chain I noticed, that the super important pair of gears in the area of the bottom chain, which are so crucial to be locked together... the narrow one lost half the gear teeth. So i am quite sure it is out of sync now and I do not know even what this part is /...

I saw some aftermarket kits and this T joint was brass so does not crack anymore. Possibly on yd25.com.au. Let us know when you have the diameters of the T joint - possibly can be found in aquarium or home improvement shops for peanuts :) Cheers

So... the "block cheater bar against the frame and use starter motor" method did not work either... Getting a 400 Nm impact wrench on Wednesday. If that fails I will go for option 1) replace only top chain and get air gun 700Nm at some point in the future. Option 2) get 700 Nm air gun. Top chain...

Thank you. As long I have the marks on cog wheels OK I do not need to worry about what is on the old chain right? I will be replacing the chains with sprockets, but I will take a close look at the teeth. In my R50 I removed the crankshaft pulley / harmonic balancer bolt with 18V battery...

Hi all. I opened the top cover and I started turning the engine to align the marks. Chain marks and cam marks do not line up... There is no paint left on the 3rd mark of the chain. I marked marks on sprockets red for better visibility. Do I need to turn it until they do, or at this point we...