Search results

Hi guys The above d 40 ute rear shoes need replacing Drums are still 295mm Linings are 55 mm wide can't seem to find 55mm linings Can anyone help? Regards XKKAT

Hi Guys I gave up on the electronic boost control valve and installed a Dawes Valve setup Boost pressures are adjustable What's the best setting? Regards XKKAT

Hi, guys Ignoring the wisdom of this forum I purchased a new Boost control valve off E bay I should have listened! It made no difference at all Still the same problem as before , Just $50 poorer Anyhow I've now fitted a Dawes valve and asking what is acceptable boost pressure for this...

So Far changed all filters - All new vacuum hoses, New Boost control valve, cleaned MAF None made any difference. I bypassed the BCV and put vacuum feed straight onto the actuator, Whee it went like a scalded cat! Until the rubber hose out of the turbo blew off its spigot with a bang! Then I...

Hi Guys I followed old Tony's words of wisdom I cleaned the MAF sensor --Replaced all vacuum lines ---Replaced the air filter and Boost control valve The violent rev rise after 2000 is gone and the car runs with less power in all gears but still dies under 2000 Whats next The turbo was...

Hi Long time member with no troubles till now! Very slow until 2000 rpm then seems ok Won't pull without going down a gear or two I will change air cleaner out But that doesn't seem to be a problem Doesn't show any codes Anyone got any ideas Regards xkkat

Hi Gang I have a Thailand-built 2013 d40 dual cab Just done timing chains, and now looking at brakes The brake pedal goes too far down before it slows for my liking! There is some confusion as to the pads number for the front. The parts guy says there are various changes and he can't be...

Hi guys Its now 3000Km since the timing chain kit job all running ok no problems whatsoever The kit fitted up perfectly and cost around $700 aust from the UK who source it out of Germany Everything you need is in the kit except the Viton "O" rings for the oil pump. The most difficult part of...

Hi Guys I asked this question about my D40 dual cab earlier but didn't find an answer. How are the cabin lights controlled The fuse called "Room light " is ok the Door open dash light is ok both front and back cabin lights wont light up I Dunno where to look regards xkkat

Hi gang just another question about my "new" truck. How far will it go after the low fuel yellow light comes on? and are there any problems if it runs out? Just asking as the nearest fuel for us is 35Km away! Thanks, XKKAT

Hi Gang My recently aquired Dual cab with tray D 40 -2.5 with 255 K on it is returning 11 litres per hundred kilometres Thats 25 MPG in the old scale any opinions on these figures is it good -bad- or average compared to your d40 vehicle regards Terry

Hi, Guys The "ROOM" lights in my dual cab don't work at all The "door open" symbol on the dash works and the "Room" fuse 10Amp is good These lights are controlled bt the Body control module but I don't know where that is There are no faults coming up on the dash. Does anyone have any...

Hi, Guys Thanks for all the help with this job. The crank technics kit went straight in and started up the first kick. The vacuum pump replacement drive sprocket goes straight on without removing the pump does not need The oil pump viton "O" rings are not included in this kit You need to make...

Hi Guys I have both front and back cabin lights out The fuse is marked "ROOM" 10 Amp .I Its unswitched meaning its straight on battery , along with the brake lights and something called "METER" anyone have any clues ? The brake lights work ok maybe meter is the memory for odometer total...

Hi Guys Has anyone tried a flogging spanner on the crank pulley centre bolt Ive tried all my rattle guns I suppose the last ditch move is to take out the starter motor and lock the flywheel ring gear! anyone got any suggestions

Hi Guys Just started stripping down The inner guide of top duplex chain has failed .It was just sitting there both mount bolts tight bit mount s had cracked off at the bend in the steel backing plate Now looking at the crankshaft pulley centre bolt Its TIGHT! Would like the forums advice...

hi all just ordered a timing chain conversion kit from UK Its made in Germany seller had good e bay reviews, BUT on further searches, after I paid they don't sound too good Don't know what I, ll get but its got to be better than whats rattling round in there now Nissan must be dumb, to...

HI all my d40 dual cab pickup has airbag assist on rear springs Has anyone tried to repair one of these . Just wondering can they be repaired like a tubless tyre?? These have been deliberately punctured ,maybe ride was too hard I don't know regards Terry

Hi All This is my first post on this list I've 'inherited a Navara Made in Thailand In my 60 years working with cars I, ve never seen anything like it! How did Nissan make a car like this! anyhow I,m stuck with it! It's on 190K and 2013 MY 2.5 diesel so far I can see it needs back...